Skip to product information
Insta360 Dual/Triple Suction Cup Car Mount

Insta360 Dual/Triple Suction Cup Car Mount

$3,179.00
Size
Style
Details

Compatible Models

X5 / X4 / X3
Ace Pro 2 / Ace Pro / Ace
GO 3S / GO 3 / GO 2
ONE RS (Dual Lens/4K) / ONE X2 / ONE R / ONE X
Insta360 Dual/Triple Suction Cup Car Mount
Insta360 Dual/Triple Suction Cup Car Mount


This car-mounted dual suction cup/triple suction cup bracket can only be used with the Insta360 high-strength invisible selfie stick. Do not use it with other selfie sticks.

Say goodbye to limitations with a unique third-person car view or other cinematic game-style perspectives

Triple suction cups form a triangular structure for maximum stability

Double suction cups suitable for driving in cities and on flat roads

Three suction cups in one design, can be split into double suction cup rack or single suction cup rack according to needs

Specifications:

Double/triple suction cup car mount x 1

Note:


1. Please follow the instructions below to install and use. Do not perform DIY or connect third-party accessories. Failure or damage caused by failure to follow the instructions is not covered by the Insta360 warranty or replacement service.

2. This accessory is not recommended for use on public roads. Please ensure that the surrounding road environment is safe before use.

3. This car-mounted double suction cup/triple suction cup holder can only be used with the Insta360 high-strength invisible selfie stick, please do not use it with other selfie sticks.

4. Please use this product in an environment with an ambient temperature of 0-40°C (32-104°F).

5. Please try to install the suction cups on the same horizontal plane (or the plane with the smallest slope). If it is not possible to install them on the same horizontal plane, the suction cups on both sides of the horizontal support rod must be attached to the same plane, and the suction cups on the extended support rod must be installed on another plane.

6. Before installing the suction cup, make sure the surface is smooth and clean.

7. When installing the suction cup, make sure it is completely attached to the flat surface. If the suction cup does not fit, loosen the knob and adjust the angle of the suction cup; reinstall the suction cup and tighten the knob.

8. Observe the indicator line after installing the suction cup. If the indicator line returns to the outside of the pump body in a short time (the indicator line can be seen outside), there is a leak and the suction cup needs to be reinstalled.

9. After installing the complete bracket, you need to make sure that all the knobs on the bracket are tightened. If the knobs cannot be tightened, or the connection of the suction cup adapter, telescopic support rod or selfie stick is still not unlocked after all the knobs are tightened, do not use the suction cup bracket.

10. When using, if you need to stop and rest, please check whether the suction cup has leaked accidentally (you can see the indicator line on the outside). If the suction cup has leaked, please reinstall the suction cup to prevent the bracket from falling and damaging the camera.

11. To remove the suction cup, use your fingers to pry the edge of the suction cup to create a gap between the suction cup and the flat surface. You can then easily remove the suction cup.

12. After use, if the surface of the suction cup is dirty, you need to wipe it clean in time to ensure that the suction cup can maintain sufficient adsorption force when used next time.

13. When assembling this vehicle-mounted three-suction cup bracket, do not use it in overly rugged off-road conditions (including but not limited to large rocks, very bumpy, steep mountain roads), and do not exceed 100 km/h (62 mph).

14. When assembling this vehicle-mounted dual suction cup bracket, please do not use it on roads other than flat asphalt roads, and do not drive the vehicle at a speed exceeding 80 km/h (50 mph).

15. The suction cup of this product adopts modular design. When using a single suction cup, it only supports connecting to the Insta360 high-strength invisible selfie stick. Keep it in a retracted state and do not unfold the selfie stick.

16. When driving, when the selfie stick is fully extended, the dynamic load of the suction cup bracket is 300g, please do not add heavy objects.

One year maintenance

Vast World Limited (Insta360 exclusive agent in Hong Kong and Macau)

Insta360 Hong Kong After-sales Service Center and Repair Services

你也許有興趣看看...